This great article below in relation to Installing A Bathtub is indeed entertaining. Don't overlook it.
Installing a bath tub isn't specifically rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately difficult job. If the old tub is easily easily accessible, the task can move immediately; if you have to open up a wall surface to remove the old bathtub as well as place the new bathtub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Make certain you have qualified on your own for the task as well as are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed project, it is better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This short article will help you install a brand-new tub in your washroom if you have actually already bought a brand-new bathtub and do not need to change the plan of your previous water pipelines.
Your devices and also material checklist need to comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic as a result of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in place with the maker supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Utilizing the two wood boards under its feet, position the bath tub in the called for position. The wood boards are valuable in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make sure that the tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bathtub up until the level reads level.
To set up taps, fit the bottom of the furthest adaptable tap port to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water system as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the tub as well as likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait till the bath tub has actually been utilized a minimum of once as this will certainly resolve it into its final setting.
Preparing for the Setup
To start with, the supporting frame supplied with the bathroom should be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets unit to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break an inflexible seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, leading to complications with dampness and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before securing, to permit the motion experienced when the tub remains in use. The sealer can split rather very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about A Step-by-Step Guide to Installing a Bathtub? Create feedback directly below. We would be pleased to hear your suggestions about this write-up. We are looking forward to see you back again later on. Sharing is good. Helping people is fun. Thanks so much for taking the time to read it.
Book Service Now